Overlander

Overlander Equipment

Overlander Motorcycles

Stainless Exhaust Manufacturers

1910  to 1930's  REPLICA AMERICAN  MOTOR CYCLE PARTS 

INDIAN HEDSTRUM & POWERPLUS PARTS –

The early Indians are a very complicated motor cycle to restore in terms of the large number of parts needed and the requirement that many of these need nickel plating. We have sort to address some of these problems by producing some of the nickel parts in stainless steel, which can be supplied in either medium polished or matt finished. The advantages of stainless steel are listed below if the correct alloy is chosen for the particular application concerned. 

A. The mechanical properties are in general better than mild steel 

B. The parts retain their bright finish better than nickelled mild steel 

C. They can be re polished easily without the need for replating 

D. Matt finished parts can be nickelled if required 

To further assist with fitting of new and old parts, we cut some holes undersize to allow you to better fit your worn components to our parts. Note that drilling stainless steel is not a problem if low speeds, sharp drills, and a suitable lubricant are used. Our Exhaust Systems are stainless steel replicas of the originals, externally. There may be some extra baffle modifications internally to strengthen and support the overhanging tail pipes etc. 

The handle bars and control group is the most complex of all the systems. The handle bars them selves are entirely made in stainless steel, while the twist grip and the flexible shaft are made of steel and are zinc plated, as these parts are well protected and are not seen. The shafting and the universal joint are all in polished stainless steel. The fittings to the frame and the control connecting rods are to be in stainless steel, as is all bright hardware.

POA

INDIAN, HEDSTROM, POWER PLUS, COMPONENTS:
YEAR PART NUMBER


N/S REAR BAND BRAKE CONTROL BRACKET  @
17+ N2370 TANK REAR CLIP-  both types @
17+ N2380 TANK FRONT & CENTRAL CLIP- both types  @
17+ N2264 HAND CLUTCH LEVER QUADRANT  @
16 9 PRIMER COVER  @
16 H5280X 3 SPEED GEAR HAND OPERATE  LEVER @
17+ N5322P 3 SPEED GEAR LEVER QUADRANT @
16+ N2232X HAND CLUTCH OPERATING LEVER @
17+ N5280K 3 SPEED GEAR HAND OPERATING LEVER @
18 N640K VALVE LIFTER RELIEF  LEVER
18 N642K VALVE LIFTER RELIEF PIVOT BRACKET @
16+ N2330 CLUTCH RELEASE FOOT LEVER @
14+ F77490 REAR TAIL LIGHT BRACKET


REAR BRAKE STOP ARM CLIP @
17+ N2212 CLUTCH LOCKING RING  + screws & washers @
17+ 19 SPEEDO MOUNTING TANK BRACKET @
13+
MUDGUARD BRACE CLIP

N/S BATTERY BOX complete @
16 H2263 HAND CLUTCH LEVER GUIDE @
9+ A17350 REAR AXLE ADJUSTMENTSCREW WASHER @
16 N254 FRONT ENGINE PLATE  s/s heavy @
16 N252/256 REAR ENGINE PLATE  s/s heavy @
9-16 A14120 HANDLE BAR GRIP CONTROL SLEEVE  Various @

  POA

13+ A14310B8000 UNIVERSAL JOINT in s/s  (lower joint & mount) @
13+ A14290/14300 UNIVERSAL JOINT in S/ Steel  (upper Joint) @
9-16 D8030X CONT.LEVER FRAME BUSH @
12+ A14020/ETC HANDLE BAR S/Steel  Various @
12+ A1419X HANDLE BAR FLEXI SHAFT  link type  @
12+   HANDLE BAR FLEXI  SHAFT unassembled kit @
9-13 A14060 HANDLE BAR STEM complete @
14-16 F14060  HANDLE BAR STEM complete @
17 N1370/4 HANDLE BAR CLAMP @
16+ N1386 HANDLE BAR CLAMP BOLTS  2 type @

N1402/1414 HANDLE BAR GRIP CONT.SLEEVE ASSLY. @

  HANDLE BAR GRIP total parts less rubber @
9+ C14090A14080  STG.STEM EXPANDER BOLT & PLUG @
9-16 B16405 STG .DOME NUT  5/8  - 1 1/8  24tpi  $15  @
9-16 411593 STG LOCK NUT  5/8  - 1 1/8 24tpi $ 10  @
9+   STG HEAD  tab washer S/S @
9-16 F14065 STG.STEM CLAMP SLEEVE NUT @
9+ N/S UPPER & LOWER BALL RACE STG.HEAD KIT set
9-16 A8210 CONT. LEVER FRAME SHAFT MAG.ADV. @
9-16 A8110 CONT. LEVER UPPER ROD  
9+ A82000 CONT.LEVER SHAFT & NUTS @
12+  D8030X CONT.LEVER FRAME STUD @
17  N808  CONT.LEVER FRAME SHAFT @
9-16 B16400 CRADLE SPRING FORK CONN. @
9-16 B16560 CRADLE SPRING FORK & PIVOT @
9-16 E21015 OIL TANK  less pump +A21010 @
17-19  N2452X OIL TANK less pump @
19-23 N2452PX OIL TANK less pump @
14+  F21035 OIL TANK  CLIP & SCREWS unf @
9+ C21012X OIL TANK & CAS TANK CAP (3 sizes) @
9+ A21040 OIL PUMP complete 2 types @
17+ N4854 FOOT BOARD  s/steel @
    FOOT BOARD CLEAT S/S @
17+  N4862 FOOT BOARD FRONT BRACKET  S/S @
14+   FOOT BOARD REAR MOUNT @
14+ F29740 MAGNETO CABLE  GUIDE & CLIP S/S @
    LOW FRICTION CONTROL CABLE  push pull @
9-16  A20100 GAS TANK CLIP S/S @
9-16   GAS TANK WITH SYRINGE @
9+ H2398 GAS TANK CLIP LEATHER WASHER @
9+ N1620X FRONT SPRING SET @
9+   FRONT & REAR SPRING EYE RUBBER  $22 @  Set






POA
 
9+ N1864X1 REAR SPRING  SET  (2 required) @
9+  D16530 FRONT SPRING PLATE  s/s @
9+ E17690 REAR SPRING PLATE  s/s @
9+   REAR SPRING CLIP  s/s @
10+  B16530 SPRING FORK BELL CRANK FRONT. various  

  LOW FRICTION CONTROL CABLE  push/pull @

  CONTROL CABLE & ANCHOR various  $15 $20  @
9+ N/S FRONT STAND @
14+ N/S FRONT STAND HOLDING CLIP assy S/S @
9+ 4500X REAR STAND @
16+ N4800 KICK START SEGMENT STUD BRACKET S/S @
16+ N4768KX KICK START SEGMENT GEAR @
17+  N254P FRONT ENGINE PLATE ELECTRIC m/s @
    FRONT ENGINE PLATE,  Hedstrum  S/S  @
    FRONT &REAR ENGINE PLATE m/s @
    FRONT ENGINE PLATE  heavy s/s @
    REAR ENGINE PLATE  heavy s/s @
12-23   ENGINE PIPES  S/Steel  With nuts  Various  @
12-18    MUFFLER ASSY SINGLE /  TWINS  $510 @
18   MUFFLER ASSY SINGLE / TWIN  $397
19-23   MUFFLER ASSY  CAST @
    CLUTCH DRUM SPROCKET REBANDED @
    BRAKE DRUM  @
    REAR SPROCKET  36 teeth @
    Engine & gear box sprockets rebanded & re hardened from  @






  POA

INDIAN SCOUT, 101 SCOUT, CHIEF, REPLICA PARTS:

CHIEF EXHAUST SYSTEM  with nuts - 1920s set
SCOUT EXHAUST SYSTEM fixed head 1 1/8" with nuts set
SCOUT EXHAUST SYSTEM push on pipes set
SCOUT EXHAUST SYSTEM screw on system with nuts set
SCOUT  101 EXHAUST SYSTEM screw on system with nuts set
SCOUT CHIEF  101 CHAIN  GUARD  @
SCOUT P/PLUS H/BAR  BRAKE  LEVER ASSY  D24280 @
SCOUT P/PLUS BRAKE BAND & LINING ASSY D24230X  N4200KN @
SCOUT P/PLUS OPERATING CAM & ARM ASSY @
SCOUT P/PLUS  BRAKE LINING & RIVETS @
SCOUT P/PLUS BRAKE  BELL CRANK & ADJUSTER  ASSY @
SCOUT P/PLUS  HEDSTRUM BRAKE DRUM (without sprocket) @
CHIEF  101 BRAKE DRUM @
SCOUT P/PLUS CONTROL CABLE ANCHORS VARIOUS from @
SCOUT P/PLUS CARBI  CONTROL CASING  CLIP S1438T @
SCOUT P/PLUS CONTROL WIRE CASING MTG. BRKT G20-24/H24-25 @
SCOUT P/PLUS TOOL BOX LOCK Stainless steel engraved Indian @
SCOUT CHIEF&101 FRONT STAND @
SCOUT CHIEF 101  REAR STAND @
SCOUT P/PLUS CHIEF 101  REAR AXLE ADJUSTING FISH PLATE  pr
SCOUT  & 101 BRAKE  PEDAL  @
SCOUT & 101  CLUTCH PEDAL & MOUNTING @
SCOUT & 101  CLUTCH LINKAGE &  ARM @
SCOUT & 101 FOOT BOARD  @
SCOUT & 101 FOOT BOARD CLEAT  @
SCOUT & 101 FOOT BOARD WITH CLEATS @
P/PLUS  FUEL TANK bare  pressed  in stainless steel pr
P/PLUS  FUEL VALVE & TOP FITTING @
P/PLUS  SCOUT & 101 FOOT BOARD RUBBER pr
P/PLUS  SCOUT & 101 " " RIVETS @
SCOUT  TAIL LIGHT BRACKET  both types @
SCOUT TAILLIGHT  BODY both types @
P/PLUS SCOUT HANDLE  BAR  TUBES pr
P/PLUS SCOUT HANDLE BAR ASSY bare pr
P/PLUS  SCOUT & 101 HANDLE BAR RUBBER pr
P/PLUS  SCOUT CHIEF $ 101 SPROCKETS  36 $ 40 teeth @
FRONT SPROCKETS REBANDED  from @
REAR SPROCKETS REBANDED from @
CLUTCH DRUM SPROCKET REPLACED  @
GEARS,  SPLINES , KEYWAYS etc  REBUILT  RE HARDENED   
SLIDER GEAR @
KICK START SEGMENT GEAR repaired @
CLUSTER GEAR  2 gears repaired  @
Engine & gear box sprockets re banded & rehardened from  @

  POA

SPLITDORF S2  MAGNETO REPLICA PARTS:
Brass cover with logo @
Cover holding plates pr
Bakelite cover @
Bakelite H.T. cable base @
Rotor @
Rotor drive gear @
Points cam @
Points set @
We are adding continually to the number of replica parts we manufacture. If a part is not listed please inquire. If a sample is available most parts can be readily made  
ACE  REPLICA PARTS:  
Foot board with cleats  @
Seat bar @
Rear guard frame mount @
Brake drum @
PERSON & MESSENGER SEAT PARTS :  
Metal  seat pan Messenger & Person from @
Messenger seat frame mount assy @
Messenger seat frame nose @
Messenger seat frame nose adjusting assy @
Seat coil springs various from  @
   
   
   



© 1997-2017 Overlander Equipment